Mother's Day Gift Idea!

Mother's Day Gift Idea!
Spoil your Mum (or yourself!) with a colourful resin bangle with a sparkly magnetic clasp. Wear one on it's own, wear a stack of monochromatic bangles or really let her personality show and wear a stack of different colours together. Peronalised sizing available so no matter what size wrist she has, there is a bangle to fit! Available at the Mill Lane Studio Resin Jewellery Shop

Monday, August 7, 2017

Hawaiian Party - Make Your Own Starfish Food Label Holders with Resin

Gold painted resin starfish food label holder

For an upcoming birthday celebration, I want to use starfish as food label holders to place in front of the platters on the food buffet but I only have one starfish so today I'm going to make a mould of it so that I can cast as many as I need. When you need to reproduce an object in quick time, then EasyMold Silicone Putty is a great choice for making your mould.

There are three parts to this tutorial: making the mould, casting the starfish in resin and finally, colouring the starfish.

Make the Mould

For this part you'll need EasyMold Silicone Putty and a starfish. You have just a few minutes to work with Silicone Putty so make sure you work quickly. Measure out equal quantities of the putty, making sure that you have enough to cover the starfish or object that you've chosen.
Measure out two equal sized balls of silicone putty large enough to cover the starfish

Place the two parts together and begin to blend them.
Part A and Part B of the silicone putty ready to mix together

Keep mixing them until the putty is uniformly coloured and there is no streaking.....
Mixing and blending the silicone putty until it is thoroughly mixed.

and then roll it into a ball.
Rolling the mixed silicone putty into a ball ready for making a mould.

Flatten it so that it is large enough to fit over the starfish.
Flattened disk of silicone putty

Centre the putty over the starfish.....
Silicone putty disk being placed over the starfish

and push the putty onto the surface making sure you press it all the way around to pick up all the detail. Try to keep the mould at least 6mm (1/4") thick, especially over the high points so that they don't make a hole. Now leave the mould to cure for 25 minutes.
Silicone putty is now covering the starfish completely.

Once it's cured, you'll be able to easily remove the starfish by gently pulling the putty away on all sides.
Gently removing the starfish from the cured mould.

Cast the Starfish

Note: I've found it best to leave the mould for 24 hours if you want to cast resin into it or you will end up with a very rough surface because of the gas that is given off whilst the putty is curing. If you're working with clay though, it's OK to use your mould straight away.

I'm casting with Castin'Craft's FastCast urethane resin. It's fast curing so it's perfect when you need a quick result. You have only a couple of minutes from the time you pour the two components together until it begins to gel, so you have to work quickly. We won't be adding any colourant to the resin because it cures white.

For this part you'll need the mould you made, FastCast, measuring cups and stir sticks or an acid brush. I've found these work better than a stir stick when you're mixing small amounts of FastCast.
FastCast resin and silicone putty moulds ready for casting.

Measure out equal quantities of Parts A and B.
Measuring out Part A of Fast Cast

The package instructions contain thorough instructions for mixing the resin but briefly, you need to stir thoroughly for at least 30 seconds, using either a disposable brush or a wooden stir stick, then pour the resin into a clean cup and use a clean brush/stir stick to mix it for another 30 seconds.
Stirring Parts A and B together with a disposable acid brush to mix them.

Pour the mixed resin to the top of the mould.
Mixed resin being poured into the silicone starfish mould.

Now, sit back and watch it change from translucent to white......
Curing resin in the starfish mould, turning from clear to white as it cures.

....right in front of your eyes!
Resin almost completely white as it is almost set.

It will only take around 10-15 minutes to harden depending on your room temperature. To remove the cast from the mould, just gently pull back the silicone on all sides and pull the starfish out.
Gently removing the cured white resin starfish from the silicone mould.

Here's the original starfish on the left and the cast resin piece on the right.
Comparing the original starfish with the resin starfish.

Make the Food Label Holders

Gold painted resin starfish holding a food label on a tropical buffet.

Cut a slit across the top with a coping saw, just wide enough and deep enough to sit a card in.
Slit being cut across the top of the resin starfish with a coping saw.

 And then to give the starfish an opulent look, spray paint it with gold paint. I used a bright gold.
Spray painting the resin starfish with gold spray paint.

Freshly painted.....
Finished gold starfish

And now it's ready to serve!
Tropical afternoon tea buffet with gold starfish food label holders.

These starfish food label holders are perfect for a Hawaiian themed buffet. I'm really happy with how they've turned out.

I'll be posting more Hawaiian themed party decor in the coming months, so keep an eye out.

Pin this for later! 
Step-by-step tutorial on how to make an easy silicone putty mould.
Step-by-step tutorial for how to cast resin starfish food label holders with quick-curing FastCast resin.


'Til next time.......











If you can't get enough of My Tutorials and you want even more inspiration, click here to find my books and printable pdfs